Optimisation of soil washing method for removal of petroleum …

Table of Contents
Issue Date

AbstractTotal petroleum hydrocarbons (TPHs), which are often found in soil, water, sediments, and air. These compounds are a type of pollutant that can have a serious negative impact on living things and human health. Soil washing method is a remediation technique used to remove contaminants from the soil. This process involves the use of water or other solvents to extract contaminants from the soil, followed by separation and disposal of the contaminated solution. This research engineered the effectiveness of soil washing method to remove TPHs from a genuine, sullied soil sample. After analyzing the physical and chemical properties of the soil, the Box-Benken Design (BBD) technique was used to optimize the variables that influence the process’s effectiveness. A quadratic model was suggested based on the BBD design, correlation coefficients, and other factors. The minimum, maximum and mean removal of TPHs during the stages of the study were 63.5, 94.5 and 76.7%, respectively. The orelation between the variables was strong, as shown by the analysis of variance (ANOVA), F-value (1064.5) and P-value (0.0001), and the proposed model was highly significant. The most effective soil washing method (SWM) was obtained with pH 7.8, liquid to solid ratio 50:1, reaction time 52 min, surfactant concentration 7.9 mg kg−1, and three washings. A removal rate of 98.8% was accomplished for TPHs from the soil in this context. The kinetic results indicate that the kinetic of TPHs removal follows the first-order kinetics (R2 = 0.96). There was not a major difference in the process’s efficiency based on temperature. The removal efficiency heightened from 0 to 150 rpm and then remained steady. Introducing air flow increased the rate of removal, and the combination of ultrasonic waves with the reaction environment increased the process efficiency and decreased the time for the process and the amount of times it needed to be washed. An analysis of the washed soil both physically and cemially revealed a substantial decrease in the concentration of other elements.
IntroductionThe rapid development of industrialization and urbanization has created soil contaminated with organic pollutants and heavy metals1. A wide range of goods and consumer products are manufactured by TPHs in many industries. In 2030, TPHs consumption will increase to 106.6 million barrels from 85 million barrels in 20162. Petroleum components are commonly released into the environment during petroleum exploration, accidents, transportation, and leaks from waste disposal or storage sites3. Near Tehran oil refinery, nearly 1,500,000 m3 of soil were contaminated by crude oil, according to a report4. Among the organic pollutants found in petroleum are alkanes, cycloalkanes, polycyclic aromatic hydrocarbons, and many other cyclic hydrocarbons. The stability and durability of these pollutants make them major environmental pollutants5. Many pollutants found in THs are harmful to the environment and difficut to degrade. Over time, these contaminants exceed their background levels and gradually migrate throughout ecosystems, causing severe environmental problems, ecological disasters, and social catastrophes worldwide. Petroleum hydrocarbon-contaminated soils have been remedied using a variety of physical, chemical, and biological methods. One of the most efficient methods of removing pollutants from soil is the SWM, which involves desorption, chelation, dissolution, and other chemical processes with the addition of specific solutions. Its advantages include flexible application, simple operation, short duration, low cost, and high removal efficiency6. An overpressure hydraulic head pushes chemicals into contaminated soil, followed by separation and treatment to remove the liquid. Soil washing is affected by numerous factors, including environmental conditions, contaminants and extraction solutions’ bonding and chelating strength. As a result,it is very important to select the right cleanng agents7. TPHs in an eluent are always mobilized by additives, even when the soil has low water solubility. Inorganic acids, bases, salts, and surfactants are common additives. Different additives have significantly different removal efficiencies for TPHs. By adding residual washing agents, soil washing technology increases environmental risks, changes the soil’s physical–chemical properties, and destroys the ecological structure. For washing technology, therefore, it is crucial to select a washing agent that removes TPHs efficiently, is non-toxic, and does not damage soil properties8,9. In the soil–water system, surfactants enhance the solubility of organic compounds in aqueous solutions. There are three categories of surfactants: anionic, cationic, and nonionic. Each of them releases its electric charge when it comes in contact with water. Among the main factors that determine surfactant performance and effectiveness are its chemical nture and its selective concentration, which is etermined by its critical micelle concentration (CMC)10. Nonionic and/or anionic surfactants are generally chosen. The biodegradability and toxicity of surfactants are also crucial parameters. Sodium dodecyl sulfate (SDS), is an organic compound with the formula CH3(CH2)11OSO3Na. There are many cleaning and hygiene products that contain anionic surfactants. It consists of sodium salts of 12-carbon organosulfates. As a detergent, this compound is amphiphilic due to its hydrocarbon tail and polar head group11. SDS were investigated for their effectiveness as contaminant removers, solvent recyclers, and cost-effective surfactant sources. Multivariate and their interactions are evaluated through fewer experimental trials due to response surface methodology (RSM). Among the principal RSM used in environment researches, BBD is the standard design12. A sandy soil contaminated with 9000 mg L−1 of cresols achieved 78.6% efficiency with an SDS soluion according to Gitipour, and Khalladi found tht a SDS solution at a concentration of 576 mg L−1 could remove diesel at a rate of 97% in soil with 94% silt13,14. The objective of this study is to improve the soil washing process to remediation of soil contaminated with TPHs based on the explanations provided. BBD applied to design the experiment, analyze the data, and determine the optimal conditions for influencing variables on soil washing (such as washing solution pH, liquid to soil ratio, SDS concentration, retention time and multi-step washing). In the optimum condition, the effect of stirring speed, airflow rate, temperature and sonication were investigated.Materials and methodsSoil sampling, preparation and characterizationThis investigation used soil samples sourced from near oil storage tanks in Tehran. In order to collect soil samples, standard methods based on authoritative references were used15. A geological information, and other features of the site can be seen in (Tabe S1). The soil samples were mixed and air-dried or 3–4 days at room temperature after collection, and homogenization was done in the laboratory through the use of a soil mixer. Samples of soil were sifted through a 2 mm sieve before examination. The soil sample was examined for physico-chemical properties and other desirable characteristics (Table 1). To ensure a significant relationship between the soil pollution near the storage tanks and the concentration of TPHs, control samples were taken from the distances of 500 and 1000 m from the storage tanks. The low concentration of the samples at distances of 500 and 1000 m indicated the relationship between the storage reservoirs and the concentration of TPHs.Table 1 Soil physico-chemical properties and other characteristics.Full size tableReagents and equipmentSodium dodecyl sulfate (SDS, CH3(CH2)11OSO3Na, 99% purity), sulfuric acid (H2SO4, 98% purity), sodium hydroxide (NaOH, 98% purity), dichloromethane (CH2Cl2, > 99.0%), methanol(CH3OH, > 99.0%), and sodium sulfate (Na2SO4, &t; 98.5%) were purchased from Merck, Samchun, and Sigma-Aldrich Co. and used with no purification. A pH meter (Portable pH meter PH-870), a digital laboratory scale (Digital Lab Science Electronic Balance, 220 g × 0.0001 g), a mechanical mixer (VONOYA Electric Overhead Stirrer, Digital Auto Stirrer with Time Setting & Speed Adjusting, 0–3000 RPM), pipet (Cole-Parmer Essentials Adjustable-Volume Pipettor, 100 to 1000 µL), centrifuge (AP9756 Economy), syringe filter (Whatman®, USA), laboratory glassware, ultrasonic Processor (60 kHz, 350 W, Qsonica 408), aeration pumps (Pondmaster AP-8 Air Pump 545 CFM), and a gas chromatograph (Agilent Technologies, model 6890 N Network GC system, USA)-flame ionization detector (FID) were used.Installing SWM reactorA 500 mL pelxi glass cylindrical unit with a diameter of 10 cm and a height of 20 cm was utilized for the SWM runs (Fig. 1). The runs were administered using a batch system at an ambient emperature of 25 ± 2 °C. One g of contaminated soilwas transferred into the reactor with 400 mL deionized-water. The reactor was equipped with the mechanical mixer, that continually mixed with 100 rpm. An air pump was used to pass air through, introducing a stable flow of air into the reaction medium by a micro-diffuser. Acid sulfuric and sodium hydroxide used to change the unique value of pH. For the measurement of TPHs, after preparing method (2–5 section), injected into GC-FID. The mean values were obtained by averaging the results of the three trials of each test. The TPHs reduction rates in the SWM were calculated with the following equation [Eq. (1)]16.$$ { ext{Efficency}};{ ext{removal}};{ ext{(\% )}} = left[ {frac{{{ ext{C}}_{{0}} – C_{t} }}{{C_{0} }}}
ight] imes 100 $$
(1)
where, Co and Ct are concentration of TPHs (ppm) in the different reaction time, respectively.Figure 1Diagram of the SWM.Full size imageOptimization of SWM variables based on BBDTooptimize the SWM for the removal of TPHs from polluted soil,through the BBD approach in the response surface method. Table 2 outlines the range of variables.Table 2 The impact of various factors on SWM.Full size tableThe BBD design was the basis for the 46 runs that are represented in Table S.2, which were to remove TPHs.The removal of TPHs from soil via SWM is represented by using a second-order polynomial model [Eq. (2)]17:$$ Y = eta_{0} + sumlimits_{i = 1}^{k} {eta_{i} } x_{i} + sumlimits_{i = 1}^{k} {eta_{ii} } x_{i}^{2} + sumlimits_{i = 1}^{k – 1} {sumlimits_{j = i + 1}^{k} {eta_{ij} } } x_{i} x_{j} + varepsilon $$
(2)
Here, Y is TPHs removal (%), β0 is the intercept, βi, βii, and βij are the linear, quadratic, and interaction effect coefficients of variables respectively, xi and xj are coded testing classes of the variables, k is the number of the independent variables, and e is the residual error. An individual numerical value was computed for eac variable with [Eq. (3)] to allow for comparison between factors withdiverse units.$$ x_{i} = frac{{X_{i} – X_{0} }}{Delta x} $$
(3)
The coded value of the variable is Xi, the gap between the highest and lowest values of the variable is ∆x, and X0 personifies the lowest value of the variable. ANOVA was conducted by applying the P-values and F-values to assess the interaction between response and factors. R2 and R2adj are correlation coefficients. In addition, R2 predicts were used.Analytical methodsTPHs levels in the soils were measured in accordance with the standard test method18. Initially, anhydrous Na2SO4 was blended with the gained soil to impede the infusion of water into the capillary column (Agilent, 30 m × 0.25 mm HP-5, USA). Subsequently, the soil samples were blended with 100 mL of a compound consisting of dichloromethane (CH2Cl2, > 99.0%) and methanol (CH3OH, > 99.0%) (3:1 volume ratio). The ultrasonic extractor was used three times for three minutesto extract the desired material, after which it was filtered through a 0.2-μm olytetrafluoroethylene (PTFE) syringe filter to separate the solid particles. Following this, a GC-FID was utilized to measure the quantity of TPHs in the solution. The column was operated with nitrogen of the highest purity as carrier gas with an initial flow rate of 2.0 mL min−1 and a post-run flow rate of 0.7 mL min−1. The oven maintained a temperature of 45 °C for 2 min before rising to 300 °C with a progression of 8 °C min–1.Supplementary investigationReaction kineticsThe TPHs removal from the soil in the optimal condition of the SWM was showed by first- and second-order model used were expressed by the following equations, respectively14.$$ { ext{C}}_{{ ext{t}}} = { ext{C}}_{{ ext{i}}} { ext{exp}}left( { – { ext{K}}_{{1}} { ext{t}}}
ight) $$
(4)
$$ {1}/{ ext{C}}_{{ ext{t}}} = { ext{2K}}_{{2}} { ext{t}} + {1}/{ ext{C}}_{{ ext{i}}} $$
(5)
where Ct (ppm), is theTPHs concentration in soil at instant t, Ci (ppm) is the initial concentration of TPHs, k1 and 2 are the rate constants of the first and second order expressed in (min) and (ppm g−1 min−1), respectively, t (min) is the time of washing.Effect of temperature, mixing speed, air flow and sonication on SWM performanceThe effect of reactor temperature (20–40 °C), mixing speed (50–300 rpm), airflow entering the reactor (0.1–1 L min−1), and sonication (60 kHz with power 350 W) on the efficiency of the SWM when operating in the optimal conditions, was investigated.Effect of soil washing on physico-chemical soil propertiesAfter washing the polluted soil, the physical and chemical characteristics of the soil were re-examined and compared with the initial values.ResultsDevelopment of a BBD, and statistical analysisThe TPHs removal results were assessed statistically to create a response surface model and identify the best conditions for SWM (Table S2). Based on the results, the minimum, maximum ad mean TPHs removal in SWM values were 63.5, 94.5 and 76.7%, respectively. According to fitting he model, quadratic model suggested (Table 3).Table 3 A summarized view of the model’s performance.Full size tableBy using the ANOVA, the results of TPHs (Table S3) showed to be highly dependable and had a very low probability value for the quadratic regression model, demonstrating that it could accurately explain the codes within the actual data and predicted values. This model was incredibly valid and proficient at predicting responses, as indicated by the correlation coefficients (R2, R2adj, and R2 predict). High correlation is present between R2, R2adj, and R2 predict, indicating that the model can predict responses19,20. The F-value and p-value in the ANOVA analysis are reliable statistical indicators for determining the data deviation factors. These indexes led to the selection of a substantial statistical model with a high F-value and a low p-value (≤ 0.05). Fisher’s F-test showed tht a quadratic model would be the most suitable to fit the relationship between the predicted and xperimental values of TPHs removal. The F-value of TPHs has been determined to be 1064.5 and the p-values (0.0001) provide clear evidence of an effective fit between the experimental and the expected response values. An Adequate Precision ratio (117.1) indicates an acceptable model21. Based on the ANOVA results, it was found that due to the physical nature of SWM, there is no significant relationship between the variables, so the mathematical relationship is simplified. The equation for the percentage of TPHs removal in SWM was expressed in terms of coded factors:$$ { ext{TPHs removal }}left( \%
ight) , = {74}/{75 } + { 5}/0{4} imes { ext{A }} + { 5}/0{2} imes { ext{B }} + { 7}/{4} imes { ext{C }} + { 4}/{9} imes { ext{D }} + { 7}/{7} imes { ext{E }} + , 0/{8} imes { ext{BD }} + , 0/0{9} imes { ext{A}}^{2} , + , 0/{6} imes { ext{B}}^{2} , + { 2}/{3} imes{ ext{C}}^{2} , + , 0/{5} imes { ext{D}}^{2} , + { 2}/{2} imes { ext{E}}^{2} $$
(6)
The impact of parameters on the removal of TPHs from SWMThrough the use of response surface plots or contour plots generated by RSM, it is possible to illustrate the interaction between variables and to pinpoint the most advantageous values for the variables.The 3D graph in (Fig. 2) displays the TPHs removal efficiency based on the five influence washing parameters in SWM. Each of the tested parameters, including washing solution pH, liquid/soil ratio, surfactant concentration, washing cycles, and retention time, had a substantial influence on TPHs removal efficiency.Figure 23D plots of significant interaction terms (washing solution pH, liquid/soil ratio, surfactant concentration, washing cycles, and retention time).Full size imageWashing solution pH effectThe efficiency of SWM in TPHs removal is significantly influenced by the washing solution pH. The results of the effect of p (4–8) on the efficiency of TPHs removal were surveyed and showed in (Fig. 2a). As the pH of the solution icreased, the efficacy of the removal of TPHs increased significantly, with the highest efficacy at pH levels slightly basic and close to 8. The negative charges of organic and inorganic components of the soil colloid surfaces are increased by the increasing of the pH of the soil solution. This proliferation of negative charge will bring about the dispersion of soil particles and the desorption of organic pollutants from the colloid surface to the washing solution, owing to the repulsion between the negatively charged heads of organic matter and soil colloids. The solubility of organic matter increases with an increase in soil solution pH, since the main organic matter constituents (humic acid and fulvic acid) are soluble in alkaline solutions. When organic material is dissolved into the soil solution, the petroleum hydrocarbon molecules that are bound tightly are also released ormade available for dissolution by surfactants by lowering surface tension10. According to a previous study cnducted on diesel-contaminated soils, an increase in pH or alkalinity was reported, extracting more diesel than when in an acidic phase, and it was found that oils are more soluble under alkaline conditions than acidic22. In Liu and coworkers’ study, remediation of diesel-contaminated soil at alkaline pH in the presence of tween 80 was better than other pH23. In addition, similar outcomes of the effect of pH were reported in Jiang and coworkers’ study24.Liquid/soil ratio effectThe effectiveness of SWM in the removal of TPHs was heavily affected by the liquid to soil ratio. The results of the effect of this parameter (20:1–60:1) on the efficiency of TPHs removal were surveyed and showed in (Fig. 2a). When the liquid to soil ratio enhanced, the elimination of TPHs significantly improved, with the highest effectiveness nearly accomplished at elevated levels. As anticipated, the appication of a substantial amount of surfactant solution facilitates the TPHs removal. By having high liquid tosoil ratio, greater TPHs concentrations are created between the two phases, thus intensifying the transfer of contaminants from the solid to the aqueous solution. Despite this, the cost of the procedure rises exponentially with the growth of the liquid to soil ratio, thus making it of utmost importance to identify the ideal value for this parameter25. Evaluation of the prior studies uncovered that the liquid to solid ratio was altered depending on the concentration and type of pollutants, the kind of surfactant, and the conditions of the soil washing process. In the study conducted by Lin and coworkers, the optimum ratio of liquid to soil was found to be 60:126. Also, in Wang and coworkers study 60:1 ratio reported as a prepare ratio in the presence of EDTA27.Surfactant concentration effectThe effectiveness of SWM in the removal of TPHs was heavily affected by the surfactant cocentration. The results of the effect of this parameter (5–10 mg kg−1) on the efficiency of TPHs removal were urveyed and showed in (Fig. 2b). Surfactants are compounds that reduce the surface tension between two liquids or between a liquid and a solid, allowing for better mixing and dispersion of the solution. The concentration of surfactant used in soil washing can have a significant effect on the efficiency of the process. At low concentrations, surfactants may not be effective in removing contaminants from soil. This is because the surface tension of the water is not reduced enough to allow for effective mixing with the contaminants. As the concentration of surfactant increases, more contaminants are solubilized and removed from the soil28,29. However, at high concentrations, surfactants can become less effective due to factors such as foam formation or precipitation of the surfactant. Foam formation can occur when too much surfactant is added to the solution, leading to reduced cntact between the solution and soil particles. Precipitation can occur when too much surfactant is added, causig it to bind with other compounds in the solution and become insoluble. Therefore, it is important to optimize the concentration of surfactant used in soil washing processes to ensure maximum efficiency while avoiding negative effects such as foam formation or precipitation. This optimization process may involve testing different concentrations of surfactant on contaminated soil samples and monitoring their effectiveness in removing contaminants29. Prior studies have found various levels of surfactants as the most favorable concentration, which is influenced by the kind and amount of pollutants in the soil, the type of surfactant and the retention time of the process30,31.Washing cycles effectThe efficacy of SWM in the removal of TPHs was profoundly affected by the washing cycles. An examination of the impact of this parameter (1–3 time) on the effectiveness of TPHs removal ws conducted and depicted in (Fig. 2c). Generally, the more times the soil washing is performed, the more successul it will be. Every washing cycle eliminates a certain amount of pollutants from the surface, and multiple washings can contribute to the removal of more pollutants. However, there are also some potential drawbacks to multiple washings. For example, excessive washing can lead to the loss of valuable nutrients and organic matter from the soil. Repeated washing may not be practical or cost-effective in all situations. Overall, the optimal washing cycles for soil remediation will depend on a variety of factors, including the type and concentration of contaminants present in the soil, as well as site-specific conditions, such as soil texture and moisture content. A thorough site assessment and careful planning are essential for achieving effective and sustainable results with soil washing7,32. In Rui and coworkers’ study, 3 time washing was reported as an optimum multi-step wasing to remediation of pollutants33. Also, in Piccolo and coworkers’ study, the highest performance to heavy metal removal was got in 3 times washing34.Retention time effectThe potency of SWM in the removal of TPHs was deeply affected by the retention time. A study of the influence of the 30–60 min parameter on TPHs removal efficiency was performed and presented in (Fig. 2d). Soil washing requires a certain length of contact between the soil and washing solution, which is known as the retention time. The effect of retention time on soil washing depends on various factors, such as the type of contaminants present in the soil, the type of washing solution used, and the soil properties. Increasing retention time can improve the efficiency of soil washing by allowing more time for the contaminants to dissolve or desorb from the soil particles and be removed by the washing solution. However, there is a limit to how much retention time can be increased before diminishing returns are observed Different pollutants may have different optimal retention times for effective removal. Increasing retention time ay also increase the amount of water required for soil washing, which can lead to higher costs and potential environmental effects, such as increased water usage and discharge. Overall, while increasing retention time can improve soil washing efficiency sometimes, it is important to consider other factors such as cost-effectiveness and environmental effects when determining optimal retention times for specific soil remediation projects28,35,36. In Bianco and coworkers’37 and Kang and coworkers38 studies, 60 min reported as an optimum retention time to PAHs removal from soil.Predicted optimum conditionFinally, we used Design-Expert software to estimate the optimal value of experiment variables for TPHs removal by SWM. pH of solution 7.8, liquid to solid ratio 50, reaction time 52 min, surfactant concentration 7.9 mg kg−1 and washing cycles 3 times were an optimum condition f SWM. In this situation, 98.8% of TPHs removed from soil. According to the prediction of the software, more than 9.9% of TPHs can be removed in the mentioned conditions. This difference can be due to measurement errors, device accuracy, the presence of interfering agents, etc. The reaction time had highest effect on SWM (7.7), then the surfactant concentration (7.4), the pH of solution (5.04), liquid to solid ratio (50.2) were effective respectively, and washing cycles (4.6) had lowest impact on SWM.Supplementary investigationReaction kineticsThe TPHs removal from the soil in the optimal condition of the SWM was showed by first- and second-order model used were expressed by the [Eqs. (4) and (5)]. The results of kinetics study at optimum condition were presented in (Table 4).Table 4 First- and second-order coefficient.Full size tableThe first-order model gave a slightly better fit to the experimental results than the second-order model, based on the square regression coefficient R2. he removal of TPHs from the soil was regulated by the first-order kinetic model. Similarly, Li and coworkers39 study and Khalladi and coworkers14 studies, first-order kinetic reported as a best model of fitting.Effect of temperature, mixing speed, air flow and sonication on SWM performanceThe effect of reactor temperature on TPHs removal performance in SWM at 20, 25, 30, 35, and 40 ºC investigated. The results illustrated in (Fig. 3). Temperature can have a significant impact on the efficiency and effectiveness of soil washing processes. Higher temperatures can increase the rate of chemical reactions and solubility of contaminants in the soil, leading to faster and more thorough removal of pollutants33. However, excessively high temperatures can also cause problems such as increased vaporization of water and chemicals, which can lead to loss of materials and reduced efficiency. Additionally, high temperatures may also cause changes in the physical properties of the soil, such as incresed viscosity or decreased permeability, which can hinder the washing process40. Therefore, it is important to contro and optimize the temperature carefully during soil washing processes to ensure maximum effectiveness while minimizing any negative effects. The analysis of (Fig. 3) shows that, within the tested temperature range, the removal performance is not significantly affected, though a minor variation is present. The temperature dependent processes control the removal, desorption, and dissolution of elements, whereas the separation of incrustation or soil-trapped TPHs is mainly determined by mechanical conditions. Consequently, this test has revealed that other parameters in TPHs could have a greater impact than temperature. In Peng and coworkers’ study, similar results were reported25.Figure 3The effect of temperature on TPHs removal in SWM (pH 7.8, L/S ratio = 50:1, surfactant concentration = 7.9 mg L−1, washing cycles = 3 times, and retention time = 52 min).Full size imageTh effect of mixing speed on TPHs removal performance in SWM at 0, 50, 100, 150, and 300 rpm investigated. The results ilustrated in (Fig. 4). The process involves mixing the contaminated soil with water and other chemicals to extract the contaminants. Therefore, the mixing speed plays a crucial role in the soil washing process performance. The effect of mixing speed on soil washing process can be summarized as follows35:

1.

Extraction efficiency: The extraction efficiency of contaminants from soil increases with increasing mixing speed. This is because higher mixing speeds create more turbulence, which enhances the contact between the soil particles and the washing solution, resulting in better extraction of contaminants.

2.

Soil particle size: The effect of mixing speed on soil particle size depends on the type of soil being washed. Higher mixing speeds break down larger particles into smaller ones, hich can increase the surface area available for contact with the washing solution.

3.

Washing time: Higher mixing speeds can reduc the required washing time by increasing the rate at which contaminants are extracted from the soil.

4.

Energy consumption: Higher mixing speeds require more energy, which can increase operating costs and environmental impacts.

5.

Equipment design: The design of equipment used for soil washing must consider the effect of mixing speed on extraction efficiency, particle size, and energy consumption.

Figure 4The effect of mixing speed on TPHs removal in SWM (pH 7.8, L/S ratio = 50:1, surfactant concentration = 7.9 mg L−1, washing cycles = 3 times, and retention time = 52 min).Full size imageIn conclusion, optimizing mixing speed is critical for achieving effective soil washing resuls. The appropriate mixing speed will depend on factors such as soil type, contaminant type and concentration, equipment design, and desired remediation goals. The findings of this study showed that the lowest performance was at zero mixing spee and the TPHs removal improved with the increasing of mixing speed until 150 rpm and then the efficiency stayed the same. In Ayele and coworkers study, similar results reported41.The effect of airflow entering the reactor on TPHs removal performance in SWM at 0, 0.1, 0.5 and 1 L min−1 investigated (Fig. 5). Airflow can have both positive and negative effects on soil washing performance. On the one hand, airflow can help to increase the efficiency of soil washing by promoting the movement of water and contaminants through the soil matrix. This is because air can help to break up soil particles and create pathways for water to flow more easily. Too much airflow can also cause problems during soil washing. For example, if there is too much air enteing the system, it can cause excessive turbulence in the water and lead to increased erosion of the soil matrix. This can cause a loss of valuable topsoil and a reduced overall effectiveness of the washing process. Overall, it is important to caefully control airflow during soil washing operations in order to optimize performance and minimize negative effects on soil quality11. In this current study, results indicated that by increasing the amount of aeration, the efficiency of the process increases.Figure 5The effect of airflow rate on TPHs removal in SWM (pH 7.8, L/S ratio = 50:1, surfactant concentration = 7.9 mg L−1, washing cycles = 3 times, and retention time = 52 min).Full size imageWhen the airflow rate was 0, 0.1, 0.5, and 1 L min−1, the efficiency of the process was 54.2, 67.9, 99.8, and 100%, respectively.The results show that the increase of airflow rates up to 0.5 L min−1 causes a significant increase in efficiency, but the efficiency is close to the values of 0.5 and 1 Lmin−1, and considering the energy consumed by the aeration pump, the value of 0.5 L min−1 was chosen as the optimal inlet air flow rate. In Tran and coworkers’ study, airflow rate was investigated as an one of the major important parameters11. InAyele and coworkers study reported that increase in air flow rate will result in more hydrophobic microbubbles being generated. So, the airflow has an impact on soil washing performance41.A study was done to assess the effect of the sonication mechanism on TPHs removal performance in SWM (Fig. 6). Sonication technology is an environmentally friendly and clean approach to treating and degrading toxic organic pollutants. Sonication is a process that uses high-frequency sound waves to agitate and dislodge particles from surfaces42. In soil washing, sonication can enhance the removal of contaminants from soil particles. The effect of the sonication mechanism on soil washing process can think by frequency, amplitude, duration, and soil type.Figure The effect of airflow rate on TPHs removal in SWM (pH 7.8, L/S ratio = 50:1, surfactant concentration = 7.9 mg L−1, washing cycles = 3 times, and retention time = 52 min).Full size imageUsing sonication enhances the rate of leaching and improves te removal efficiency by diffusion into the outermost layer. The utilization of ultrasonic processes for leaching produces higher removal efficiency with a quicker processing time. Sonication technology applied to soil systems might enhance the desorption of pollutants by disintegrating the soil structure. The conceptual dependence of desorption of contaminants from the soil surface is largely determined by changes in Gibbs energy (∆G°) of a system43. In this study, in the presence of ultrasonic waves, the removal rate of TPHs occurs in a shorter time. Also, in a one-step wash, all of TPHs were separated from the soil. In Effendi and coworkers study, the effect of ultrasonic mechanism to remediation of polluted soil was investigated44.Effect o soil washing on physico-chemical soil propertiesWe evaluated the effect of SWM on the physical and chemical characteristics of the soil in an optimal condition (Fig. 7). The effect of soil washing on physico-chemical soil properties depends on sevral factors, including the type and concentration of contaminants, the type of washing solution used, and the duration and intensity of washing. SWM can alter soil texture by removing fine particles such as clay and silt, which are more likely to be contaminated than coarser sand particles. This can cause changes in soil structure, porosity, and water-holding capacity. SWM can change soil pH by removing or adding ions that affect acidity or alkalinity. SWM can remove organic matter and nutrients along with contaminants if the washing solution is too strong or if the duration of washing is too long and can reduce cation exchange capacity (CEC) by removing cation-exchange sites along with contaminants45. Based on results, significant changes wre observed in the measured values. The soil pH was increased from 7.21 to 8.29 and CEC was also reduced from 2.47 to 1.95 (cmol/kg). In Bari and coworkers’ study, similar results were reported46.Figure 7Changes of trace and major elements during sol washing.Full size imageIn the end, in Table 5, different processes are presented in remediation soil contaminated with petroleum hydrocarbons.Table 5 Various studies in petroleum hydrocarbons removal from soil.Full size tableConclusionThis study optimized the performance of SWM to remove TPHs from a real contaminated soil sample. After sampling and determining the physico-chemical characteristics of the soil, optimization of variables affecting the efficiency of the process was done by the BBD method. Based on the BBD design and the correlation coefficients and other indicators, the quadratic model was proposed. The minimum, maximum and mean removal of TPHs during the stages of the study were 63.5, 94.5 and 76.7%, respectively. Based on AOVA and indices F-value (1064.5) and p-value (0.0001), there was a high correlation between the variables and the proposed model was significant. The best results of SWM were achieved by pH of 7.8, liquid to solid ratio of 50:1, reaction time of 52 mn, surfactant concentration of 7.9 mg kg−1 and washing cycles of three times. 98.8% of TPHs were removed from the soil under this circumstance. Based on the kinetic results, the kinetic of TPHs removal follows the first-order kinetics (R2 = 0.96). The efficiency of the process was not affected significantly by temperature. The removal efficiency intensified from 0 to 150 rpm and then sustained its steady state. The incoming air flow improved the removal efficiency, and ultrasonic waves in the reaction environment improved the process efficiency and reduced the process retention time and the washing cycles times. After the physico-chemical analysis of the washed soil, it was found that the concentration of other elements has decreased signiicantly.

Data availability

The datasets generated and analyzed during the current study available from the corresponding author on reasonable request.
ReferencesXue, Y., Chen, L., Xiang, L., Zhou, Y. & Wang, T. Experimental invetigation on electromagnetic induction thermal desorption for remediation of petroleum hydrocarbons contaminated soil. J. Environ. Manag. 328, 117200. https://doi.org/10.1016/j.jenvman.2022.117200 (2023).Article 
CAS 

Google Scholar 
Ambaye, T. G. et al. Remediation of soil polluted with petroleum hydrocarbons, and their reuse for agriculture: Recent progress, challenges, and perspectives. Chemosphere 1, 133572 (2022).Article 
ADS 

Google Scholar 
Ghoreishi, G., Alemzadeh, A., Mojarrad, M. & Djavaheri, M. Bioremediation capability and characterization of bacteria isolated from petroleum contaminated soils in Iran. Sustain. Environ. Res. 27, 195–202 (2017).Article 
CAS 

Google Scholar 
Kebria, D. Y., Khodadadi, A., Ganjidoust, H., Badkoubi, A. & Amoozegar, M. Isolation and characterization of a novel native Bacillus strain capable of degrading diesel fuel. Int. J. Environ. Sci. Technol. 6, 435–442 (2009).Article 
CAS 

Google Scholar 
Ambye, T. G. et al. Microbial electrochemical bioremediation of petroleum hydrocarbons (PHCs) pollution: Recent advances and outlook. Chem. Eng. J. 452, 139372 (2023).Article 

Google Scholar 
Gu, F. et al. A review for recent advances on soil washing remediation technologies. Bull. Environ. Contam. Toxicol. 109, 651–658 (2022).Article 
CAS 
PubMed 

Google Scholar 
Liu, J. et al. A critical review on soil washing during soil remediation for heavy metals and organic pollutants. Int. J. Environ. Sci. Technol. 19, 1–24 (2021).
Google Scholar 
Zheng, X.-J. et al. Remediation of heavy metal-contaminated soils with soil washing: A review. Sustaiability 14, 13058 (2022).Article 
CAS 

Google Scholar 
Mehralipour, J., Darvishali, S., Bagheri, S. & Kermani, M. Photocatalytic-ozonation process in oxytetracycline degradation in aqueous solution: Composite characterization, optimization, energy consumption, and by-products. Sci. Rep. 13, 11113 (2023).Article 
ADS 
CAS 
PubMed 
PubMed Central 

Google Scholar 
Caetano, G., Machado, R. D. M., Neiva Correia, M. J. & Marrucho, I. M. Remediation of soils contaminated with total petroleum hydrocarbons through soil washing with surfactant solutions. Environ. Technol. 14, 1–24 (2023).Article 

Google Scholar 
Tran, H. T., Lin, C., Hoang, H. G., Bui, X. T. & Vu, C. T. Soil washing for the remediation of dioxin-contaminated soil: A review. J. Hazard. Mater. 421, 126767 (2022).Article 
CAS 
PubMed 

Google Scholar 
Barabadi, H. et al. Optimization of myco-synthesized silver nanoparticles by response surfce methodology employing Box–Behnken design. Inorg. Nano-Metal Chem. 49, 33–43 (2019).Article 
CAS 

Google Scholar 
Gitipour, S., Narenjkar, K., Sanati Farvash, E. & Asghari, H. Soil flushing of cresols contaminated soil: Application of nonionic and ionic surfactants under different pH and concentrations. J. Environ. Health Sci. Eng. 12, 1–6 (204).Article 

Google Scholar 
Khalladi, R., Benhabiles, O., Bentahar, F. & Moulai-Mostefa, N. Surfactant remediation of diesel fuel polluted soil. J. Hazard. Mater. 164, 1179–1184 (2009).Article 
CAS 
PubMed 

Google Scholar 
Carter, M. R. & Gregorich, E. G. Soil Sampling and Methods of Analysis (CRC Press, 2007).Book 

Google Scholar 
Naciri, Y. et al. Preparation, characterization and photocatalytic degradation of Rhodamine B dye over a novel Zn3(PO4)2/BiPO4 catalyst. J. Environ. Chem. Eng. 7, 103075. https://doi.org/10.1016/j.jece.2019.103075 (2019).Article 
AS 

Google Scholar 
Kermani, M., Mehralipour, J. & Kakavandi, B. Photo-assisted electroperoxone of 2, 4-dichlorophenoxy acetic acid herbicide: Kinetic, synergistic and optimization by response surface methodology. J. Water Process Eng. 32, 100971 (2019).Article 

Google Scholar 
Seo, S.-J., Kim, J.-H., Shin, J.-W. & Park, J.-Y. Treatment of artificial and real co-contminated soil by an enhanced electrokinetic-Fenton process with a soil flushing method. Water Air Soil Pollut. 226, 1–14 (2015).Article 
CAS 

Google Scholar 
Danmaliki, G. I., Saleh, T. A. & Shamsuddeen, A. A. Response surface methodology optimization of adsorptive desulfurization on nickel/activated carbon. Chem. Eng. J. 313, 993–1003. https://doi.org/10.1016/j.cej.2016.10.141 (2017).Article 
CAS 

Google Scholar 
Arslan, A., Topkaya, E., Bingöl, D. & Veli, S. Removal of anionic surfactant sodium dodecyl sulfate from aqueous solutions byO3/UV/H2O2 advanced oxidation process: Process optimization with response surface methodology approach. Sustain. Environ. Res. 28, 65–71 (2018).Article 
CAS 

Google Scholar 
Iqbal, M., Iqbal, N., Bhatti, I. A., Ahmad, N. & Zahid, M. Response surface methodology application in optimization of cadmium adsorption by shoe waste: A good option of waste mitigation by waste. Ecol. Eng. 88, 265–275 (2016).Article 

Google Scholar 
Salehian, E., Khodadadi, A. & Hosseini, B. Remediation of diesel contaminated soils using surfactants: Coulumn study. Am. J. Environ. Sci. https://doi.org/10.3844/ajessp.2012.352.359 (2012).Article 

Google Scholar 
Liu, C. et al. Efficiency of diesel-contaminated soil washing with different tween 80 surfactant concentrations, pH, and bentonite ratios. Environ. Res. 214, 113830. https://doi.org/10.1016/j.envres.2022.113830 (2022).Article 
CAS 
PubMed 

Google Scholar 
Jiang, Y. F., Sun, H. Yves, U. J., Li, H. & Hu, X. F. Impact of biochar produced from post-harvest residue on the adsorption behavior of diesel oil on loess soil. Environ. Geochem. Health 38, 243–253 (2016).Article 
CAS 
PubMed 

Google Scholar 
Peng, S., Wu, W. & Chen, J. Removal of PAHs with surfactant-enhanced soil washing: Influencing factors and removal effectiveness. Chemosphere 82, 1173–1177 (2011).Article 
ADS 
CAS 
PubMed 

Google Schola 
Lin, K.-Y., Chen, Y.-M., Chen, L.-F., Wang, M.-K. & Liu, C.-C. Remediation of arsenic-contaminated soil using alkaline extractable organic carbon solution prepared from wine-processing waste sludge. Soil Sedim. Contam. Int. J. 26, 569–583 (2017).Article 
CAS 

Google Scholar 
Wang, Y., Zhang, B., Deng, T. & Li, F. Reclamation of EDTA by sodium tetraethylenepentamine-multi dithiocarbamate after soil washing process with EDTA. Environ. Earth Sci. 76, 1–10 (2017).Article 

Google cholar 
Offiong, N.-A.O., Fatunla, O. K., Essien, J. P., Yang, C. & Dong, J. Soil washing of total petroleum and polycyclic aromatic hydrocarbons from crude oil-contaminated ultisol using aqueous extracts of waterleaf. Environ. Technol. 44, 35–44 (2023).Article 
CAS 
PubMed 

Google Scholar 
Ma, Y. et al. Efficient removal of polybrominated diphenyl ethers from soil washing effluent by dummy molecular imprinted adsorbents: Selectivity and mechanisms. J. Environ. Sci. 29, 45–57 (2023).Article 

Google Scholar 
Mukhopadhyay, S., Hashim, M. A., Sahu, J. N., Yusoff, I. & Gupta, B. S. Comparison of a plant based natural surfactant with SDS for washing of As(V) from Fe rich soil. J. Environ. Sci. 25, 2247–2256. https://doi.org/10.1016/S1001-0742(12)60295-2 (2013).Article 
CAS 

Google Scholar 
Zhang, M. et al. Organo-layered double hydroxides for the removal of polycyclic aromatic hydrocarbons from soil washing effluents cotaining high concentrations of surfactants. J. Hazard. Mater. 373, 678–686 (2019).Article 
CAS 
PubMed 

Google Scholar 
Grimison, C. et al. The efficacy of soil washing for the remediation of per-and poly-fluoroalkyl substances (PFASs) in the field. J. Hazard. Mater. 445, 130441 (2023).Article 
CAS 
PubMed 

Google Scholar 
Rui, D. et al. Remediation of Cd-and Pb-contaminated clay soils through combined freeze-thaw and soil washing. J. Hazard. Mater. 369, 87–95 (2019).Article 
CAS 
Pubed 

Google Scholar 
Piccolo, A., Spaccini, R., De Martino, A., Scognamiglio, F. & di Meo, V. Soil washing with solutions of humic substances from manure compost removes heavy metal contaminants as a function of humic molecular composition. Chemosphere 225, 150–156. https://doi.org/10.1016/j.chemosphere.2019.03.019 (2019).Article 
ADS 
CAS 
PubMed 

Google Scholar 
Srivastava, V., Puri, M., Srivastava, T., Nidheesh, P.& Kumar, M. S. Integrated soil washing and bioreactor systems for the treatment of hexachlorocyclohexane contaminated soil: A review on enhanced degradation mechanisms, and factors affecting soil washing and bioreactor performances. Environ. Res. 208, 112752 (2022).Article 
CAS 
PubMed 

Google Scholar 
Vidal, J., Báez, M. E., Calzadilla, W., Aranda, M. & Salazar, R. Removal of chloridazon and its metabolites from soil and soil washing water by electrochemical processes. Electrochim. Acta 425, 140682 (2022).Article 
CAS 

Google Scholar 
Bianco, F., Monteverde, G., Race, M., Papirio, S. & Esposito, G. Comparing performances, costs and energy balance of ex situ remediation processes for PAH-contaminated marine sediments. Environ. Sci. Pollut. Res. 27, 19363–19374 (2020).Article 
CAS 

Google Scholar 
Kang, C.-U. et al. Pyrolytic remediation of crude oil-contaminated soil. Sci. Total Environ. 713, 136498 (2020).Article 
ADS 
CAS 
PubMed 

Google Scholar 
Li, B. et al. Remediation of Cd(II) ions in aqueous and soil phases using novel porous cellulose/chitosan composite spheres loaded with zero-valent iron nanoparticles. React. Funct. Polym. 173, 105210 (2022).Article 
CAS 

Google Scholar 
Liu, Y. et al. Pyrolysis of heavy hydrocarbons in weathered petroleum-contaminated soil enhanced with inexpensive additives at low temperatures. J. Clean. Prod. 302, 127017 (2021).Article 
CAS 

Google Scholar 
Ayele, B. A., Lu, J. & Chen, Q. Optimization of aeratio enhanced surfactant soil washing for remediation of diesel-contaminated soils using response surface methodology. PeerJ 8, e8578 (2020).Article 
PubMed 
PubMed Central 

Google Scholar 
Wang, J. et al. Review on the treatment of organic pollutants in water by ultrasonic technology. Ultrason. Sonochem. 55, 273–278 (2019).Article 
CAS 
PubMed 

Google Scholar 
Lei, Y.-J. et al. Insights into the oxidation kinetics and mechanism of diesel hydrocarbons by ultrasound activated persulfate in a soil system. Chem. Eng. J. 378, 122253 (2019).Article 
CAS 

Google Scholar 
Effendi, A. J., Wulandari, M. & Setiadi, T. Ultrasonic application in contaminated soil remediation. Curr. Opin. Environ. Sci. Health 12, 66–71. https://doi.org/10.1016/j.coesh.2019.09.009 (2019).Article 

Google Scholar 
Mohammed, A. E., Salam, K. A. & Samuel, S. S. Application of soil washing treatment method for the remediation of petroleum polluted soil. in Research Anthoogy on Emerging Techniques in Environmental Remediation, 236–261 (2022).Bari, A. F., Lamb, D., MacFarlane, G. R. & Rahman, M. M. Soil washing of arsenic from mixed contaminated abandoned mine soils and fate of arsenic after washing. Chemosphere 296, 134053 (2022).Article 
ADS 

Google Scholar 
Xia, C., Liu, Q., Zhao, L., Wang, L. & Tang, J Enhanced degradation of petroleum hydrocarbons in soil by FeS@BC activated persulfate and its mechanism. Sep. Purif. Technol. 282, 120060. https://doi.org/10.1016/j.seppur.2021.120060 (2022).Article 
CAS 

Google Scholar 
Su, Q. et al. Microbial removal of petroleum hydrocarbons from contaminated soil under arsenic stress. Toxics 11, 143 (2023).Article 
CAS 
PubMed 
PubMed Central 

Google Scholar 
Wang, Y. et al. Optimization of conditions for a surfactant-producing strain and application to petroleum hydrocarbon-contaminated soil bioremediation. Colloids Surf. B 213, 112428. https://doi.org/10.1016/j.colsurb.2022.112428 (2022).Article 
CAS 

Google Scholar 
Li, X., Xu, J. & Yang, Z. Efficient oriented interfacial oxidation of petroleum hydrocarbons by functionalized Fe/N co-doped biochar-mediated heterogeneous Fenton for heavily contaminated soil remediation. Chem. Eng. J. 450, 138466. https://doi.org/10.1016/j.cej.2022.38466 (2022).Article 
CAS 

Google Scholar 
Download referencesAcknowledgementsThis study was supported by the Azad University West Tehran Branch.Author informationAuthors and AffiliationsDepartment of Environment, West Tehran Branch, Islamic Azad University, Tehran, IranPouyan Zoghi & Roya MafigholamiAuthorsPouyan ZoghiView author publicationsYou can also search for this author in
PubMed Google ScholarRoya MafigholamiView author publicationsYou can also search for this author in
PubMed Google ScholarContributionsP.Z.: Writing—original draft, Methodology. R.M.: Writing—review & editing, Methodology, Software, Supervision, Project adinistration, Investigation, Funding acquisition.Corresponding authorCorrespondence to
Roya Mafigholami.Ethics declarations

Competing interests
The authors declare no competing interests.

Additional informationPublisher’s noteSpringer Nature remains neutral with regard to jurisdictonal claims in published maps and institutional affiliations.Supplementary InformationSupplementary Tables.Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the artcle’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
Reprins and PermissionsAbout this articleCite this articleZoghi, P., Mafigholami, R. Optimisation of soil washing method for removal of petroleum hydrocarbons from contaminated soil around oil storage tanks using response surface methodology.
Sci Rep 13, 15457 (2023). https://doi.org/10.1038/s41598-023-42777-9Download citationReceived: 19 May 2023Accepted: 14 September 2023Published: 19 September 2023DOI: https://doi.org/10.1038/s41598-023-42777-9Share this articleAnyone you share the following link with will be able to read this content:Get shareable linkSorry, a shareable link is not currently available for this article.Copy to clipboard
Provided by the Springer Nature SharedIt content-sharing initiatve

CommentsBy submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.